which rcbs mould for 44 mag?

[SweetMk]

I've been shooting an RCBS 240 SWCGC since the late 80s. It's a very accurate bullet out of a TC 44, Ruger and Taurus.

Lets say I get this mold, and handles, and cast the bullets from WW's,,,

Can I size then shoot the bullets WITHOUT gas checks at lower velocities??
It seems the bullet would look a little like a boattail with the missing gas check,,, so it seems like it would work.

I love shooting my 44 MAG 629 S&W,,, but, since, almost exclusively I shoot low velocity, the gas check seems like a waste of $$$,,,
(the purpose of Cast Boolits is to save $$,,, right??)

(I assume the gas check is to allow higher velocity??)

The RCBS 240 SWCGC seems to be super popular,, do I have to buy a different mold for bullets W/O gas checks??

[Mica_Hiebert]

Lets say I get this mold, and handles, and cast the bullets from WW's,,,

Can I size then shoot the bullets WITHOUT gas checks at lower velocities??
It seems the bullet would look a little like a boattail with the missing gas check,,, so it seems like it would work.

I love shooting my 44 MAG 629 S&W,,, but, since, almost exclusively I shoot low velocity, the gas check seems like a waste of $$$,,,
(the purpose of Cast Boolits is to save $$,,, right??)

(I assume the gas check is to allow higher velocity??)

The RCBS 240 SWCGC seems to be super popular,, do I have to buy a different mold for bullets W/O gas checks??

They have the 245 grain swc that is checkless I believe it is the same bullet just 5 grains heavier since lead fills the check area.

[Lloyd Smale]

never had much luck shooting gas checked bullet designs without a gas check. I guess it depends on what you want. Me I look for good groups at 25 yards. I like to see one inch 6 shot groups. Now if your idea of shooting is hitting a coffee can at 25 yards then they will probably be fine

[GWM]

I like a boolit that is accurate out to 200 yards. I had the 240-SWC-GC but it didn't work for me (in the S&W 629). I now use a custom Mountain Mold that looks more like the 240-SIL but drops at .434". For accuracy the right diameter can be important.

[Nowherefound]

Just out of curiosity, lots of 44-240 and 44-245 recommendations here. Is there a reason the 44-250-k hasn't popped up? Recently entered the 44 world and it is the only mold I have for it at the moment.

[Lloyd Smale]

The 245, 250k and 250kt are decent bullets. There all worth trying but in my opinion if I wanted a non gas checked bullet id just by a lyman 429421. couple more good gas check molds are the 429244 a 429214

Just out of curiosity, lots of 44-240 and 44-245 recommendations here. Is there a reason the 44-250-k hasn't popped up? Recently entered the 44 world and it is the only mold I have for it at the moment.

[Mica_Hiebert]

I will probably be going with the 240 swc GC even tho the GC adds cost they seem to be more forgiving in the bore size department. I really needed more calibers to load for like I needed a hole in my head. The 240 sil gets lots of love but the meplat isn't big enough for my liking I want a general purpose bullet and even tho I may take a longer range pot shot at a steel dinger from time to time I am probly not good enough of a shot to notice the difference between bullet types at longer ranges. Once I get a gun sighted in I generally never shoot a group at least with my plinking guns.

[Petrol & Powder]

I hate gas checks on handgun bullets and see little need or them at sane velocities. Acting on advice from others on this forum I went with the RCBS 44-250-K [SWC] and I have been pleased with that decision.

[Mica_Hiebert]

I hate gas checks on handgun bullets and see little need or them at sane velocities. Acting on advice from others on this forum I went with the RCBS 44-250-K [SWC] and I have been pleased with that decision.

What do you consider sane velocities? It's a 44 MAGNUM after all

[Petrol & Powder]

Based on your post #14:
"I purchased both this 44 and my 41 because they where good deals and you can always use more guns so they don't really have a "purpose" I have my 357/38 that's my go to plinker then I have my SRH 480 for hunting... the 41 mag and 44 mag I just now own and need something to feed them rcbs only has 1 41 mould so it's an easy choice. "

I assumed you were not selecting a dedicated hunting bullet.
Just because you can shoot full power magnum loads doesn't mean you have to every time you pull the trigger. With that in mind, I think less than 1200 fps and in reality, often a lot less.

I like simple logistics to the point that simplifying my equipment often takes precedence over seeking maximum performance. Just because you can do something doesn't mean you must. By choice, I only have a few loads for 44 Magnum. My all-around load (and also my favorite 44 load) is a Skeeter 44 Special equivalent loaded in a 44 Magnum case using that RCBS 250 SWC bullet cast with 20:1 alloy. That load will do 90% of what you need a 44 to do. For that remaining 10% I have a couple of hotter loads, one of which uses that same bullet. (that's the simple logistics thing showing ).
Your goals are likely different than mine. If I need a gas check I'm just going to go with a jacketed bullet and call it a day.
YMMV.

By the way, that RCBS 44-250-K mold has proven to be an excellent mold and it produces a very useful all-around bullet.

Good Luck!

[Lloyd Smale]

are they needed NO. Are they beneficial you bet. Are they worth the added cost. that I guess is a personal decision. I will say this. Ive been loading for handguns for over 40 years and have owned near a hundred different handguns in that time. Ive shot MANY different bullets through all of them. I don't recall a single gun (other then something like a 45acp that doesn't have gas checked molds) that didn't do its absolute best work with a gas checked bullet.

Yes in some cases the differences were small and in some cases I didn't test a lot of bullets finding a superb load. Gas checked bullets are just easier to find good loads for and I may have stopped testing when I found a tack driving load before I might have found one with a plain based mold. My take on it is this. Probably on average if I take a good gas checked bullet and start load development it takes 1/2 the time and components to fine tune the load and it shoots better in the end then a plain based bullet and that is doubly so if I want to use a softer alloy for my bullets or the speeds get up above 1100 fps with anything but the hardest alloys. Also I can buy near 10 gas checks for every jacketed bullet I buy. 3-4 cents a gas check is in a different category to me then 30 cents a bullet .

Now I'm not going to bs anyone. I shoot a lot of plain based bullets too. I shoot ALOT and even I don't want to buck up for the cost of gas checks for everything but when I need a gun to do its best theres usually a gas check in it and in those cases the cost doesn't matter. I guess it comes down to what your looking for. I know guys that wont buck up for 4 or 5 different powders to try or different primers ect to find the most accuracy out of there guns either. Some are happy rolling beer cans at 15 yards and if your one of those then don't bother with gas checks.

The 250k is a decent bullet. Ive found better plain based bullets but its a decent one. In most of my 44s it will do 2 inch or a bit more at 25 yards with some load development and with extensive load development maybe a bit under two inch. Ive had some guns that would do 1.5 with it but don't recall any doing better. If that's good enough for you. Personaly I look for 2 inch 50 yard groups as a minimum with hunting guns. But that's me.

I hate gas checks on handgun bullets and see little need or them at sane velocities. Acting on advice from others on this forum I went with the RCBS 44-250-K [SWC] and I have been pleased with that decision.

[GWM]

It's not just bore size, it's the cylinder throats. I would recommend measuring the throats. An RCBS mold may cast too small to fit the throats. A GC may help a bit. If it wasn't restricted to RCBS only I would consider one of the custom makers and get a slight oversize.

[LUCKYDAWG13]

I know your asking about RCBS molds but this is a real good boolit http://www.accuratemolds.com/bullet_...=43-265F-D.png
shoots very good in my Ruger SBH

[Mica_Hiebert]

I like my custom NOE moulds but I just found out I get a awesome discount on rcbs products enough to steer me twards the rcbs mould instead of a custom. I already ordered some rcbs handles for my NOE mould. I'd be happy with minute of beer can at 50 yards from a seated position. I'm pretty sure I'll be going with the 240 swc GC.

[Lloyd Smale]

my take on it is like this. I do like swc's and keiths. there just old school looking. But other then a few gas checked swcs there all mediocure shooters. Now an lfn or rf design will about allways shoot well but its going to have to be at least 260 grain in my opinion to be a real shooter. 280 is even better. With an lfn you will probably get an accurate bullet without even using a gas check. there a lot less finiky. If you take a good swc like a 240 rcbs and change it so minutely that you cant even tell with the naked eye you can and probably will ruin a good design. Ive seen many times on there that I got into group buys for swcs that were copys of bullets that were proven shooter and the custom molds copy shot like ****. Lfns are much more forgiving. Most all of them shoot well. If you don't mind a bit more recoil a 280 lfn is hard to beat for an all around 44 mag bullet. Youll get a lot of arguments about this but an lfn design is hands down the easiest design to find accuracy with. Problem is rcbs doesn't make one.

I know your asking about RCBS molds but this is a real good boolit http://www.accuratemolds.com/bullet_...=43-265F-D.png
shoots very good in my Ruger SBH