what press do you have

[specops]

Lee Reloader with Universal Decapper next to tumbler
Lee Classic Cast for rifle cartridges
Classic Turret I just bought for .223 and other volume rifle cartridges
Pro 1000s set up for .380, 9mm, .38 Special, .357 Mag, .44 Special, .44 Mag, .45 ACP and .45 Colt
Lyman Spartan Turret for working up pistol loads

[mikenbarb]

These are old pics but this just a few of what I own. I currently have 18 rifle and pistol setups and 7 for shotshell. My favorite is the old Hollywood 12 station turret. Yes, I have an illness! LOL.

[Adam10mm]

Dillon 550, Dillon 1050, RCBS Rockchucker, Lee Hand Press, Lee Classic Turret, MEC 600JR 20ga

[newrugersafan]

I'm a piker when it comes to some of you guys.

Just two LocknLoad AP and a Redding T-7



I know it looks like a small space but there is a drop down desk in the chest on the left and a big desk on the right so I can spread out.

Mike

[chrismetallica1]

reloading press, just curios

So far

One Lyman Rockchucker
One RCBS Rock chucker supreme
Two Lee Reloaders
Two Lee Breechlock challengers
One Redding Cast press 7-1
One Lee Load All
One MEC 600jr
One Pacific - 105
One Leet Turret 4 hole
One Lee Turret 3 hole
One Lyman All American

Old Picture . Need to take a new one of the other bench

[Matt_G]

I used to have four presses; now I only have three. I traded my first press (RCBS Partner) to a fellow forum member for some linotype a few months back.

RockChucker II does all my rifle stuff, some pistol (small batches) and all depriming. I deprime and tumble my cases before loading.


RCBS Ammomaster does most of the pistol stuff. It may do my 22-250 in the future too depending on the volume needed.


MEC 9000G 12 gauge. That thing has loaded many thousands of trap loads for me.

[wv109323]

1 Rockchucker
1 Star for .38 Special
1 Star for .45 ACP
1 Dillon 550B for .357 , 32-20, .223, .38 Super
1 Ponsness-Warren 375 in 20, 16, 12 Gauge
1 Pacific Super

[Ozark Howler]

Well...

1 P-W Metalmatic
1 RCBS RS
1 RCBS JR
2 RCBS 2A's
1 RCBS "A"
1 RCBS "Pre A"
1 Herter's Super 3
1 Lieb 2 Stage "H"
2 Dietmeyer DL300's
1 Pacific 155 Auto
1 Pacific DL100
1 MEC Sizemaster
1 MEC 650
1 MEC Versamatic

All working and in like new condition........do I really need all of these?

[Pavogrande]

My small lot --
A small C&H C press using ram shellholders --

Herters #3 for most work -

Lachmiller -- Kept in reserve -- very close copy of the herters, rather herters is a copy of the lachmiller - nice that the shellholders are the same

Since lachmiller had no priming feature, a nice lachmiller bench primer is in service. I do believe RCBS modified and kept it in their line after acquiring lachmiller-

Almost forgot -- Lyman Tong (310)

[Gerry N.]

Pacific Super Deluxe C bought mid '63. (This is the one that gets used.)
Lee reloader bought the week that press was introduced. (sizing and priming)
Lyman 310 in half a dozen calibers. (In a drawer in my camper.)
Lee Loaders in half a dozen different calibers. (In the same drawer.)
Lee 4-hole Turret. ( Getting used more and more as it becomes more familiar.)

Gerry N.

[robertbank]

Dillon 550B
RCBS Supreme11

Take Care

Bob

[milsuplvr]

I have

Pacific Multi-Power C
Pacific 07
Lyman Hand Press

Love old equipment

Presses I no longer have but have given to my son

CH Single stage
RCBS Jr

[Fugowii]

Dillon 550B - Does all my rifle and pistol - no need (for me) for anything else.

[Charlie Two Tracks]

Lee 4 hole turrret

[Cadman1979]

Dillon XL650. Loading for 45acp, 9mm and 223 remington. Started out w/just the basic XL650 press and added the auto-case feeder system later on. Dillon equip does cost more than a lot of presses/equip out there but their no bs warranty and customer service are tops. I also like their pistol dies as you can easily remove/replace the seating die stem to clean the die w/out losing your setting. Actually kind of wish I would have been the guy that invented them.

[JesterGrin_1]

Charlie I am sorry but your picture is too small can you make it BIGGER lol. Clean Desk I must say

[.357]

Started on a Lyman accupress, loaded a ton of ammo on it and it's still going strong, if missing most of it's paint.
Lee pro 1000 set up for 45 acp
Lyman orange crusher
Lee loadmaster that is in pieces under my bench but that will eventually be set up for .223

Kind of want a 550 not sure for what since i have my bases pretty well covered.

[EMC45]

Currently I have on my bench a RockChucker (rifle), a Lee Classic Cast (pistol) and a Lee "C" Frame press for decapping and bullet sizing duties. On my other bench I have a Lyman 4500 "C" clamped to it, also have a MEC Sizemaster in 12ga. that was given to me on the floor that also gets clamped on when needed. Have another MEC that has been cannabalized for parts, but I use it for 20ga. loading (yes it turns out a nice shell).

[smokemjoe]

Herters Super Model 3 and a few Rockchuckers, 2 Lee - 1000s, Lee and RCBs juniors for outside on the bench.

[WallyM3]

I decided to take the Co-Ax plunge. The companion A2 is a recent gift from a good chum with whom I build rifles. What a monstah! (The press, not the chum.)

I make long and short handles with 1.5" phenolic balls for each press. (Haven't gotten to the A2 yet.)