How's this?
https://www.snipershide.com/shooting/attachments/1597326980432-png.7397581/
Type: Posts; User: 36g
Forum: Cast Boolits
How's this?
https://www.snipershide.com/shooting/attachments/1597326980432-png.7397581/
Forum: Cast Boolits
The 7.62X39 case is interesting to work with, especially now that boxer brass is more readily available.
Just for something different I made up a wildcat heavy barrelled AK in 6.5X39. Load data is...
Forum: Cast Boolits
I put together a 6mm PPC in 2008 on an AR upper. As I recall it functioned just fine (87 gr. J-Words) and I got it on paper at 100 but have never really done the follow-up load development. I'll have...
Forum: Cast Boolits
So, what's the advantage of 6mm ARC vs. 6mm PPC?
Forum: Cookin' Recipe's
Depends - for just heat, Tabasco. For Hot and Sour Soup - Siracha. For general TexMex = Choulula Chili Lime.
Forum: Gunsmithing Tips & Tricks
Drill a small hole in it and use a tap out/tap extractor to remove the stub.
Forum: CB Loads / Military Rifles
#10 has a Garand loading section as well.
Forum: CB Loads / Military Rifles
Well, it started as an add on non-functional prop for an upcoming movie but I figured that it would be just as easy to make a functional one. Then, if there is a functional one why not actually work...
Forum: CB Loads / Military Rifles
PC'd the cast bullets that I had purchased that started at .310", after PC'ing they came out to .312-.313 so now have some more load work up to do.
Forum: Our Town
I've found EvapoRust to work well. It's basically non-hazardous (just don't drink it) and probably is a combination of citric and oxalic acids plus maybe some EDTA. It won't harm solid metal, only...
Forum: CB Loads / Military Rifles
Suppressor is done and registered.
326400
326401
326402
Have run several 180 gr jacketed loads using H4895 that seem promising - still need to run them over a chrony and check group size....
Forum: Our Town
Was Huntington Die Specialties an inherent part of RCBS or a separate entity?
Forum: CB Loads / Military Rifles
Thanks again for your guidance! The .308 subsonic data was what I have been reviewing having come to the same reasoning as you in regards to case capacity and basic bore dimensions. I might even have...
Forum: CB Loads / Military Rifles
While waiting for some heavy cast boolits, I loaded up a few Sierra 190 gr. Spitzers (.311 dia.) with 7.5 gr. of Bullseye (plus some standard velocity with IMR 4350). Standard velocity fired fine (no...
Forum: Military Rifles
Nice catch! Any suggestions?
I'm thinking of sectioning a bullet but am a bit hesitant as I don't want to discover that it has an incendiary element...
Forum: Military Rifles
As noted, they have maroon tips, not red. Red tip would have been WWII vintage tracers (later changed to orange post WWII). M2 would be black tip - AP. The maroon appears to be the M62A1 tracers as...
Forum: Military Rifles
The color is similar to that used on Soviet/Russian API or APIT ammo but those should be .310-.312" diameter. Perhaps a straight incendiary round?
Forum: Military Rifles
I have acquired a few J-Words that I haven't ID'd yet. They are .308 diameter, military, 145 gr., with a maroon colored painted tip. As can be seen in the photo they are a closed based tracer at a...
Forum: CB Loads / Military Rifles
Thanks for the info! In general, would loads for .45 ACP (200 - 230 grain bullets) seem to be a relatively good starting point? I hadn't though about the flash hole but that makes a lot of sense...
Forum: CB Loads / Military Rifles
Looking for recommendations for some subsonic heavy boolit CB loads for a suppressed Mosin Nagant.
Working up plans for an updated (internals) BraMit style suppressor and need a starting load...
...
Forum: Black Powder Cartridge
Here are a couple of conversions of 1858 Remingtons using Kirst/Richards style design. These were in .44 C&B then .45 Colt. These were done for Sam Worthington's use in The Last Son movie.
325775
Forum: Black Powder Cartridge
If you are thinking of a .36 C&B conversion be aware that the conversion cylinders are typically .38 Special. Bullet diameter for .38 SPL is .358 and bore diameter for .36 C&B is .375. Options are to...
Forum: Shot Guns
I finally completed the Remington barrel installation. Just needed a spacer tube to bridge the distance from the front barrel ring to the magazine cap. Made one out of aluminum tubing and then coated...
Forum: Military Rifles
A rimmed cartridge should headspace on the rim, not the shoulder. The chamber can actually be somewhat sloppy from that standpoint as the shoulder just needs to allow the cartridge to chamber....
Forum: Muzzleloading.
My understanding is that for the fastest ignition from the pan the powder in the pan should be tilted away from the flash hole so that you don't get a fuse effect but rather the flash from the pan...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |