Theres a box of Remington kleen bore 22 rim fires in my grandfathers tackle box the price tag reads 19 cents.
Type: Posts; User: country gent
Forum: Cast Boolits
Theres a box of Remington kleen bore 22 rim fires in my grandfathers tackle box the price tag reads 19 cents.
Forum: Cast Boolits
I would buy Portuguese surplus 7.62 ball ammo for practice at 129.00 / 1000 case.
Forum: Cookin' Recipe's
eggplants fall into the same way. the one year Moms eggplants really produced, all the neighbors started locking there cars afraid of "donations"
Forum: Special Projects
Working on the toe jack I need a tap extension so made this set today they are 10" long #10-1/2" taps. Slots drive the taps square head, taps slide in and can be replaced easily when needed. Was...
Forum: Single Shot Guns
Some front sights dont have enough area for tapes to work good. clay can be used all around but is a paint to form out so you get a good flat side and square front and back
Forum: Single Shot Guns
Error X sight radius / range in inches will get you very close.
A trick Ive done is build the sight up with JB weld epoxy to see where you need to be for sure.
A couple small pieces of flat...
The charmay (sp) I ran had a flat orbit for doing threads that should work. That sub routine burnt down the radially out.
I used alot of copper electrodes and some carbide ones also. carbon is...
Forum: Cookin' Recipe's
Dads and my way were to feed all the cauliflower and broccoli we could to the steers then eat the steaks. :)
Some like to season the mould by pre heating it several times to get the patina started on it. You do want to pre heat the mould as brass sucks a lot of heat till it gets up to temp. It heats very...
Forum: Black Powder Cartridge
Bought a thompsen center renegade kit in 50 cal to get the extra deer season in ohio. actually used for slug gun season also I was more comfortable with it than the shotgun and slugs.
Then around...
Forum: Cast Boolits
I have worked with the 155 sierra palma bullet, 168 HPBT both sierra and hornady, 175 sierra. All worked good in the 1-10 twist in my service rifles.I normally competed from 200 yds to 1000yds. This...
Forum: Our Town
Great to here from you. Get better soon. Dont let it win. Never give up
Forum: Special Projects
The hilt and back aree probably pins , but the scales could be headed rivets. Not a big thing replacing scales as the heads can be drilled out.
What wood are you planning on using?
I made a 3 piece...
Forum: CB Loads / Military Rifles
On the line front sights were smoked with a carbide lantern for the very darkest dullest black. this stood out and there was no glare from light as the day changed. The national match front is...
Forum: CB Loads / Military Rifles
Forward and right about 2:00 is the normal ejection pattern for the garand except for the last round from a clip. This can be adjusted by clipping the ejector spring and or stoning a slightly...
Forum: Cookin' Recipe's
The best sausage gravy is with sausage from the butchers shop. Once a year we would have a pig ground into whole hog sausage this had a little more fat than today's prepackaged. ( you didnt have to...
Forum: Vintage Reloading Gear
Wilson, Redding and Warner would make dies to your fired cases send them 3-5 fired cases and they would make the die to match them.
This was more popular back in the 50s and 60s when wildcating...
It may be the bullet sliding rust or scale on the plate against the steel and producing a red hot ember or spark.This only really shows up at dusk or low light.
Forum: Single Shot Guns
I want to say 47 grns but Im also loading a 350 grn bullet in the starline case. This is for BPCR silhouettesin my high wall and hepburn
Forum: Single Shot Guns
38-55 isnt hard to load and no real "special" things need to be done. Its a straight forward cartridge to load. Use good data. Work up the load from starting load.
The 38-55 will really shine with...
Forum: CB Loads / Military Rifles
Well when our club had the same thing ( a developer was behind it) the bullets supposedly came from a house wall and roof, gravel driveway and lawns. again no rifling and also no distortion from...
Forum: Gunsmithing Tips & Tricks
Mom made Dads and my aprons ( later my wife) she had a pattern that was very nice and made them from white denim. They had 3 pockets 2 were up near the top 1 held pencil and 6" scale these were only...
Happy top have helped PopcornSutton, Hope the conversion met your expectations.
0-1 is ground tool steel much flatter and square to start with. Hence it saves having to square and true the stock....
Forum: Cast Boolits
The soft nose casting isnt to bad with the right equipment and set up. I occasionally cast 45 caliber rifle bullets with a soft nose.
I have 2 ladles one is small and holds a measured amount of lead...
Forum: AirGuns
Several hurricanes released exotic animals in larger numbers over the years. These animals arnt "native" to the area and have no natural predators or other means of control. They breed and reproduce...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |