Search:

Thanks to Larry Gibson for pressure testing in in his Oehler 43 PBL.

AND these have been pressure tested not to exceed 20,000 psi. While exceeding SAAMI MAP for .44-40 these are well within safe design limits for heat treated post-1920 Colt New Service, Winchester...

The .44 Magnum and .44-40 have almost identical powder capacity. There is no issue using .44-40 data to assemble reduced power .44 Magnum ammo. A charge of 6-7 grains of Bullseye or TiteGroup works...

You can mail a personal check with paper copy application printed from back cover of The Fouling Shot.

Join the CBA and buy a set of CD archives of The Fouling Shot.

In use roll crimp .45 Auto Rim or .455 Webley dies with .45 Colt shell holder.

That FN58 ammo is Berdan primed. Not worth the effort.

One drop only of 2- cycle oil on the sprue plate pivot screw. One drop only on a Q-tip to lightly lubricate the alignment pin bushings. With new mold boil blocks in tap water with a squirt of Dawn...

I see no need for the .327. I have two Ruger Blackhawks in .30 Carbine. One with 7-1/2" barrel and the other professionally shortened to 5-1/4". The .30 Carbine with full charge factory loads beats...

USAA Half Century Member. Both home and auto. One house fire, one tornado two cars totalled when struck by drunk drivers. No complaints.

You can increase the Bullseye to 2.5 grains in the I-frame or 3 grains in a J-frame or 3.0 and 3.5 of 231. These should not be exceeded if you want the guns to last.

MEASURE the cylinder throat diameters with zz- minus pin gages or by driving a dead-soft, pure lead round ball through each charge hole and measuring with a micrometer. For a rifle do a pound cast of...

In the Cowboy load section?

No .32-20 data there I could find.

Water filled gallon plastic water jugs. At least four deep.

Agree. The kids today do not measure. We may have met years ago when I was at Ruger and I believe you may have been at New Haven, CT Winchester. Enjoy your posts. Jay Jarvis and Dave Zaidan were a...

With Accurate Molds you can specify alloy and indicate whether you want the 0.002 tolerance positive, negative or centered. I order most molds with nose tolerance negative to enter cylinder thoats...

Important to cast chamber and origin of rifling and to also slug barrel. All three of my Beretta 9mm pistols are .357-.358 groove, but chambers run tight so that it is absolutely necessary to select...

OAL. is 1.60

My design from Accurate I use in .32 S&W Long, .32 H&R Mag and .32-20 is 31-105T.

Tom can make in plain base if you object to the bevel and can adjust diameters.

I load 2.5 grains of Bullseye...

My very first rifle was the clip- fed version of what you have, the model 511. Great guns. Wish I had kept mine.

In what caliber? For which rifle or revolver?

4227 is too slow burning to work well in .45 Colt.

Lyman has 4227 data for .454 Casull.

I'm with Larry. Solid advice.

The pre-WW2 Colt D-frames and non-heat treated pre-1929 Army Specials must be treated gently like the pre-1918 S&Ws.

An Official Police .32-20 or post-1920 Colt SA can handle heavier loads as...

My S&W 4th change shoots to the fixed sights at 25 yards with the Accurate 31-105T and 3.5 grains of Bullseye for 850 fps from a 4-inch barrel.

For a heavier hunting I load 5 grains of AutoComp...