You can load them backwards, but you don't need to if you're loading "midrange" (target-velocity) loads or for defense/protection. They don't have to expand because they're already full-caliber and...
Type: Posts; User: 96wa6
You can load them backwards, but you don't need to if you're loading "midrange" (target-velocity) loads or for defense/protection. They don't have to expand because they're already full-caliber and...
Forum: Cast Boolits
Jim: I'm new here and back to casting (after three decades or so).
I hope you don't mind a somewhat unrelated question: Where did that sprue cutter lever come from??? I NEED A COUPLE OF THOSE...
No slam, no harm meant.
a) You can't use moon clips (1/3, 1/2 or full) in the Ruger. Only in guns designed for them. Check out the gap on the back of a 1917 Colt or Smith, or a 1955(?) Target/25-2...
Forum: Cast Boolits
Okay, I've searched but can't seem to find this.
Everyone says 'the boolit should be sized to your revolver's cylinder throats.'
Okay, I give.
Does that mean it barely slides through the...
Forum: Cast Boolits
The throats on those breech-seat rifles are usually specially cut to seat special tapered bullets with many "rings" that look sort of like Lee tumble-lube bullets. Each ring from the nose down...
Forum: Cast Boolits
How does one use Bullplate on the plunger? Where does one put it? Just paint it on? Let dry? Etc?
Forum: Cast Boolits
If you DON'T have a .38, the acquisition pretty much requires you get one. I was at a gun show and saw old RCBS custom dies in .17 Mach IV for $10. Had to buy them. Then had to buy a .17 Mach IV...
Forum: Boolit Lube !
The plugged holes aren't leaking and that's not what I'm asking. Guess I don't write so good. I think the last two posters might have it right; too much heat making the lube too soft and, therefore,...
Forum: Boolit Lube !
Sorry, I left that part out. Yes, the double holes are filled with shot. I have the punch adjusted well, so that the lube is centered in and flowing only into the lube groove. I moved it up and down...
Forum: Boolit Lube !
I'm still getting the hang of my Star, and would like to ask a couple of things from you veterans. Basically, I'm getting both too much lube and not enough, both at the same time.
I use a little...
Forum: Lead and Lead Alloys
I have an elevated level. They thought it was because I shoot a lot of Bullseye, inhaling smoke. It might add to it, but it might have something to do with casting musket balls in my basement without...
Forum: Cast Boolits
Gang:
I just tried Red Dot in the .45 Colt for the first time and I need to know if you guys actually chrono-ed your loads. 6.0-gr. gave me 707 fps avg., and 6.5 gave me 756 fps avg., each of 12...
Forum: Reloading Equipment
Hey, just found this thread;
I inherited a PILE of ancient primers, so thanks for the 'splainin'.
One I haven't seen mentioned is a "shotshell" primer that looks like a rifle primer. Are these...
Forum: Group Buy Archives
Okay. Two more questions;
1) I saw on some of the galleries two different kinds of HP pin systems; one that is remeniscent of Lymans, where the pin is removable and has a wood knob on it, the...
Forum: Group Buy Archives
I'm in, and whole hog. I'll get funds in the mail tomorrow for a 5-holer.
Best,
96wa6
Question, though. I've always liked two holes in my game, one entry and one exit. What's the thought...
Forum: Cast Boolits
Aha! Groove diameter! Uhm, ideally, what should it be? Like .001" under cyl. throats?
96wa6
Forum: Cast Boolits
Hi, gang. Lurker here.
I have a question about sizing cast slugs for .45 Colt. I have 3: a Ruger Bisley 5-1/2", a Smith Mountain Revolver, and a Smith 25-7.
The Ruger has throats from .450 to...
Hey, a subject I know something about! Newby here. Bullseye shooting is my main sport. I was coached by a gunsmith who was once Chief Pistolsmith of the Army Marksmanship Unit for 13 years. I learned...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |