https://castboolits.gunloads.com/showthread.php?73836-quot-h-108-quot&highlight=H108+data
My lot data is almost identical to AA9 data with AA9 data, which I have to extrapolate starting loads in...
Type: Posts; User: BK7saum
Forum: Factory & Surplus Powder
https://castboolits.gunloads.com/showthread.php?73836-quot-h-108-quot&highlight=H108+data
My lot data is almost identical to AA9 data with AA9 data, which I have to extrapolate starting loads in...
Forum: Factory & Surplus Powder
If you email them, they should provide you with the data. I have about 6 lbs left. Data sheet is stuck somewhere in a loading manual. That data was also posted here in a previos thread.
Forum: Special Projects
I use the lapping bar to set up my rings. I feel that gets me closer than the "alignment" bars.
Forum: Leverguns
Do you reload for it or shoot factory ammo?
If it was mine and I reloaded, then it is a non issue. push the shoulders back 0.002-0.003" reload and shoot. When reloading, you set the headspace of...
Forum: Casting Equipment
Maybe it is time to get a new burner. I have had the 3 I use for 15-20 years. Yeah bugs or trash have clogged them over the years but, so far they always clean out an burn very well when I use a...
Forum: Casting Equipment
If you have a spider web or mud dauber blockage, blowing it out with air is not going to remove or completely remove the obstruction.
Speer makes/made a 110 RN/HP for the 30 carbine with the exposed lead hollowpoint. They work well at subsonic velocities on varmints.
They should be explosive in the 300WM if they survive the...
You run into diminishing returns with lighter amd lighter bullets where a 3006 will give almost the sme velocities as same bullet in 300 WM. I would consider the 110-125 grain bullets.
The 110...
Forum: Casting Equipment
Second checking the interior of the burner for obstruction. i have had mud daubers or other insects clog or partially obstruct the passage through the burner, reducing flow and getting a yellow...
Forum: Gunsmithing Tips & Tricks
Set the end of the barrel in a metal can or other chemical resistant container to catch any seeping or leak.
Forum: Gunsmithing Tips & Tricks
I would probably just make a cork from a dowel or use a wine cork.
Rubber is likely to degrade and fail. Anything more chemical resistant would be hard to source and expensive for a one time use.
Forum: Factory & Surplus Powder
Yes, same powder in different containers, not to be confused with powders of similar burn rates.
Forum: Gunsmithing Tips & Tricks
Why cant you plug the barrel and fill it up?
Forum: Casting Equipment
Also sounds like your ram and die are out of alignment. I have used a flat punch in the past due to this exact reason.
Forum: Testing Area
This email...
Dear BK7saum,
We have had a few issues with the website lately as far as people showing up as being banned when they were not suppose to. If you visit the website and it shows...
When I was practicing for firearms instructor school, I dry fired at least 10 times more than I shot live ammo. The course was a PPC match 5, IIRC, and I also dry fired and utilized dummy round...
Low is rolling the wrist or anticipating the recoil. The cure for this is to dry fire. Once you can dry fire and the sights do not move off the target, you have improved your technique.
The...
Dry fire, Dry fire, Dry fire is the cure for many improper trigger techniques.
Is this shooting 1 handed or 2 handed?
Likely too much finger on the trigger. Try the center of the pad of your...
Forum: Cast Boolits
I have to wonder if you will ever get this barrel to shoot without leading. If the chamber is in spec, you are probably going to have trouble getting a fat 0.359 (minimum) or a 0.360/0.361 bullet to...
Forum: Shot Loads For Pistols
Just fill the cavity of a seating stem with hot glue and shave flat with a razor blade or knife. Then you are pushing a flat capsule with a flat seater plug.
It is now cataloged as a 360-313-FN
https://noebulletmolds.com/site/shop/bullet-moulds/358/360-313-fn-ax2/360-310-fn-2-cavity-pb-thumper/
If you have a 358 mold already, I would buy a custom sizer 0.001-0.002 over your groove diameter and size boolits you already have available. They will shoot just fine.
If you don't have a mold...
!!!!!Nobody is saying screw the die all the way in for the caliber the die was designed for!!!!!
The case mouth is nominally 0.008" (0.327") smaller than the FCD desgnated caliber (0.335")
This...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |