That's over my pay grade, I've used it and tested it and use it if I'm in a hurry for light loads, but never went very far with it.
Type: Posts; User: randyrat
Forum: Boolit Lube !
That's over my pay grade, I've used it and tested it and use it if I'm in a hurry for light loads, but never went very far with it.
Forum: Boolit Lube !
I just sent No1 the fee for selling on the VS section...I will be selling, but a bit slower than before..took me forever to get my life back from hell (injury with Covid at the same time, bout kicked...
Forum: Boolit Lube !
I'll be back in the VS section soon, had to take some time off. Finally getting some time and material inventory built back up. Please don't message me yet, not until I am back as a Vendor Sponsor, I...
Forum: Cast Boolits
Never let Politics get in your way of friends, we all put up with each others views. They are more conservative then they realize, but I'm not telling them that. We have more in common than not in...
Forum: Cast Boolits
Time to get ready and be prepared...Been casting 45 acp and loading 2-300 at a time for years and now it is time to be better prepared. Time to bulk up and have more on hand. Who knows what could...
Forum: Coatings and Alternatives
Reviving this thread
I'm not into powder coating much, but I want it in my tool box..One big question was hardness? 400 Deg F for 20 min or so is definitely
mess up the hardness, even if you water...
Forum: Factory Rifles
Congrats !!!
Excellent rifle and Caliper to play with.
Forum: Casting Equipment
Cleaning and scrapping more often stops the drip. Sharpen a thin stick to scrape around the bottom of the pot especially around the valve and the inside and your dripping will be way less. Use a...
Forum: Swaging
Just ID ing here and all selling will be done in the appropriate area.
Forum: Swaging
A friend of mine bought out a bunch of reloading equipment and supplies, noticed a bunch of Swagging stuff.
Eventually I'm gonna need help IDing this and selling it.
Don't think he is gonna want...
Forum: Boolit Lube !
I have sold several tons of beeswax on here as a Vendor Sponsor, but time is rare for me now. So if you want to sell beeswax here I doubt there will be any competition, would be happy to give advice....
Forum: Cast Boolits
I need to get back to my 30-30 and work up Sub Sonic loads again.
This thread reminds me the fun I had finding the best accurate subsonic loads in the 30-30 using pistol powders. I'm going a bit...
Forum: Boolit Lube !
I am selling a similar product if your interested in the VS section..As of today just PM me for prices and directions.
Mine is called "ZIP LUBE"
Forum: Cast Boolits
A while ago I ran a similar test, although my bullets where all sized at .451...I believe the TAC 1 gained me dang near 2" at 75' with about 2 different shake on lubes.
Now TAC 1 is my go to for...
Forum: Boolit Lube !
Speed green is slightly lees than 1/3 oils to 16 ounces beeswax.... 5 ounces of added oils anymore and it with purge.
I am selling TAC1 bullet lube now in the VS section
Forum: Reloading Equipment
Shooting 45ACP a lot, I don't have time nor the patients to tumble brass. Using Citric Acid and a bit of Dawn soap in hot water, rinse real good and then lay the Brass out to dry thoroughly works...
Forum: Factory Rifles
Just imagine, an AR15 platform (less weight than the AR10), same mags, basically same brass sized up .257 6.5 mm (thinking 80 to 100 grain), only a barrel change, all of this with more thumb than the...
Forum: CB Loads / Military Rifles
Your NOE drops bullets at about 170 grain.Here is some cast bullet loads using Red Dot and 170 grain bullet
http://www.gmdr.com/lever/lowveldata.htm
Forum: Vintage Ammo
Chances are, I will pull them down and reload them..I'll save em for some long range shots towards evening.
I would think it is Visa Versa; (point not less than 75 yards and not greater than 900...
Forum: Military Rifles
Well, for the money I have in this gun, it is no sweat to destroy the receiver...The gunsmith did say it was a bit soft, but was fine for cast bullets..I just don't know and value mine or someone...
Forum: Vintage Ammo
I have some 30-06 Orange tipped tracers head stamped TW 53 Are these type 10 or M32 or what? are they worth collecting.
I wouldn't mind shooting them if I knew they were safe or just collect...
Forum: Military Rifles
I have a Nation Ordnance 1903A3- sportorized, paid $100 for it..I had it tested by a very qualified gun smith. The gun smith tested the hardness and head spacing, all seamed fine but recommended...
Forum: Reloading Equipment
If you look around, maybe appliance stores, ask for a used stove hood with an exhaust fan that works. Set the hood up near the window, exhaust it out the window and save your self tons of...
BP | Bronze Point | IMR | Improved Military Rifle | PTD | Pointed |
BR | Bench Rest | M | Magnum | RN | Round Nose |
BT | Boat Tail | PL | Power-Lokt | SP | Soft Point |
C | Compressed Charge | PR | Primer | SPCL | Soft Point "Core-Lokt" |
HP | Hollow Point | PSPCL | Pointed Soft Point "Core Lokt" | C.O.L. | Cartridge Overall Length |
PSP | Pointed Soft Point | Spz | Spitzer Point | SBT | Spitzer Boat Tail |
LRN | Lead Round Nose | LWC | Lead Wad Cutter | LSWC | Lead Semi Wad Cutter |
GC | Gas Check |