Search:

Amen!

Rupture resolved! Get the lead out!!!

Cartridges plunked in the Lyman cartridge checker. Cartridges plunked in the barrel after picking out the lead. Went back out to the range and chambered one...

326635

326636

I scraped these pieces of lead from the end of the chamber. They were exactly where the cartridge headspaces.

326631

I noticed the rounds don’t “plunk” when I was attempting to get this photo.

Now I’m thinking maybe it fired slightly out of battery?

I don’t think the 147 grain bullet weight is incompatible with the carbine. As a matter of fact, I took a whitetail with a 147 grain XTP several years back. I’ve used 115 through 200 grain...

9x19
I looked at a recipe from the Vihtavuori app with a recipe for a 145 grain H&N plated round nose. 2.6 grains of N310 powder. (3.3 max) 1.142” oal. Predicted velocity of 794 FPS.

I...

I admit to using a fast powder and smaller charge getting more rounds per pound.

So day one of lubrisizer. Got some lube on the base of the boolets. Wiped it off with a paper towel, because I...

326624

I tried out my new to me lube/sizer and was excited about having loaded rounds that weren’t sticky with LLA. The lube in it is soft and tacky but I’m thrifty and using it and learning.
...

I’d trade you some brand name bullets or buy outright for the AP bullets. I don’t shoot on a public range and they would be fun to try on old junk cars and other ornaments we collect in Tennessee. ...

Ground pork
Sage
Black pepper
Red pepper
Sea salt

That was my sausage recipe.

You should look at permissible levels of heavy metals on municipal sewer discharge permits across the nation.

I use a Big Berkey water filter for my drinking water.

Good luck next weekend!!

Yes. I’m using Precision Spherical Buffer. Just like the tri-ball loads. The wad petals are about 0.007” thinner on the BPI wads vs the precision reloading wads. I didn’t...

Static electricity?
Plastic coating traveling through the air hitting a grounded target.

326574

Well I’m not sure what contributed more to wad failure?

I used a BPI multi metal wad cut down instead of the Precision Reloading wad. Secondly the stack was too short so I tried a flex...

Don’t the lead free primers use larger than standard flash holes too?

I’ve had issues with two different Marlin rifles with peep sights. Probably ’80s vintage. The tube around the front sight looked twisted on a 30-30. I thought the gunsmith bent it during...

What did y’all end up with?

326562

Well, I did it! Thank you all for the helpful tips!!!

I started at kindergarten level though. Lee Mold was running great! One of those sessions that you hate to stop because it’s working...

I have been looking at the website already. I’m concerned about their pricing. Possibly the decimal point needs to move one place to the right? $3.50 doesn’t seem like correct pricing for 100 wads.

I found some 1-1/2 ounce lead shot loads in the BPI Advantages manual, 6th edition, using the MM1275 wads which look similar to the TUPRW12 wads with Blue Dot and Longshot that could be used as a...

326554

Tuprw12 wad with three 0.600” balls inside.
Looking like either the three inch for the tri-ball load or the 2-3/4” wad will need to be trimmed up using two balls in a 2-3/4” load

I’m intentionally reviving this thread...

A thought I had while reading this thread is mismatched ball sizes for the tuprw12 wads. Use a .575-.600” on the bottom and a slightly larger upper ball,...

Thanks! Brass molds sure are good looking!

I’ve been pondering a double .600 ball load. The tri-ball is impressive! Maybe even excessive. Single .600 ball is nice. 44 mag carbine territory. I’d like some tips for your double ball recipe if...

Look carefully at the bullet shape of the bullet of the Federal 22 Punch defensive ammunition.

I’d wager they put some research into it.